1. Home
  2. Bulk Density Of Aggregates According To Is

Bulk Density Of Aggregates According To Is

Aug 24, 2020 M = bulk density of the aggregate, lb/ft 3 [kg/m 3] S = bulk specific gravity (dry basis) W = density of water, 62.3 lb/ft 3 [998 kg/m 3]. Report. Report the results for the bulk density to the nearest 1 lb/ft3 [10 kg/m3] as follows: Bulk density by rodding; Bulk density by jigging; Loose bulk density.

Send Email:[email protected]

Send Message Chat Online

Popular Articles

focus

Properties Of Recycled Aggregate Concrete

of cement mortar in the total mass of aggregates, so the bulk density is accordingly lower. According to practical experience, it was shown that the bulk density of recycled aggregate was on the average by 10% lower compared to the bulk density of natural aggregates [6,9,10]. 2.5. Crushing and abrasion resistance Mechanical properties of ...

Learn More

Concrete Aggregates: Effects And Classification Civil ...

Normal-weight aggregate: An aggregate with a unit weight of 1520–1680 kg/m3 is classified as normal-weight aggregate. Sand, gravel, and crushed rock belong to this category and are most widely used. Concrete made with this type of aggregate has a bulk density of 2300–2400 kg/m3. It is the main concrete used to produce important structural ...

Learn More

Understanding The Density Of Concrete • Aggregate …

As for concrete itself, the density of concrete of normal weight is about 2,400 kg per cubic meter, or 145 lbs. per cubic foot. The concrete density varies depending on the amount and density of the aggregate, how much air is entrapped or purposely entrained, the cement concentration, and the maximum size of aggregate used.

Learn More

Lightweight Concrete: Light Weight Aggregate Concrete ...

The aggregates used in this concrete is basically passing through and retained on 10 mm and is mixed with the aggregate/cement ratio of 6:1 to 10:1. The strength controlling parameters in no-fines concrete are water-cement ratio, aggregate cement ratio, and density of concrete. Fig. below shows the relationship among these parameters.

Learn More

Properties Of Different Grades Of Concrete Using Mix ...

The average bulk densities of uncompacted and compacted sand were found to be 1422 kg/m and 1538kg/m respectively. The crushed stones used have specific gravity of 2.63, and a compacted and un compacted bulk densities of 1415kg/m3 and 1326kg/m respectively, which clarified it as normal weight aggregates. The values of density recorded

Learn More

Recycled Aggregate Concrete: Experimental Shear Resistance ...

Aug 01, 2012 Particle density and water absorption were measured according to European standard EN 1097–6 and loose bulk density and volume of voids according to EN 1097–3 . All RCA-concrete mixtures (RC-C-1 to 3) were made of 100% wt RCA in the coarse (4–32 mm) as …

Learn More

Cost Evaluation Of Producing Different …

The corresponding concrete has a bulk density less than 1800 kg/m . (Cinder, blast furnace slag, volcanic pumice). ii. Normal weight aggregate: This type 3has unit weight of 1520-1680 kg/m . The concrete made with this type of aggregate has a bulk density of 2300-2400 kg/m3. iii.

Learn More

Classification Of Concrete Bis

Classic (ordinary) concrete with bulk density from 1900 kg/m3 to 2500 kg/m3 and; Heavy-weight concrete with bulk density of higher than 2500 kg/m3. High bulk density of concrete is achieved by using heavy-weight aggregates, such as barite, iron ore (magnetite, hematite and limonite), splinters or specially made balls of iron and steel.

Learn More

What Are The Properties Of Aggregates For Concrete ...

Oct 01, 2016 Specific gravity of major aggregates falls within the range of 2.6 to 2.9. Specific gravity values are also used while designing concrete mix. Also read: Specific Gravity & Water Absorption Test of Aggregates. 5. Bulk Density. It is defined as the weight of the aggregate required to fill a container of unit volume. It is generally expressed in ...

Learn More